GMC Envoy Denali @ Schrier Automotive

www.schrierautomotive.com City 15 21 (5.3L engine/4-speed auto trans),Luggage rack roof-mounted Black adjustable with center rails,Fascia front Denali-specific with fog and cornering lamps,Fascia rear Denali specific with step pad,Moldings body-color bodyside Denali-specific,Grille bright honey-comb,Fog lamps front round halogen,Daytime Running Lamps,Headlamps dual halogen composite with automatic exterior lamp control and flash-to-pass feature,Headlamps washer,Lamps cornering,Mirrors outside heated power-adjustable manual-folding with integrated turn signal indicators and memory (Body-color on Denali.),Assist steps Denali-specific color-keyed,Glass Solar-Ray deep tinted (all windows except light-tinted glass on windshield and driver- and front passenger-side glass),Wipers front intermittent with washers,Wipers rear intermittent with washer,License plate bracket front (available at no extra charge),Body liftgate with liftglass electric release and rear-window wiper/washer,Seats front bucket with leather seating surfaces 8-way power driver and front passenger seat adjusters power lumbar control adjustable outboard head restraints and storage pocket,Seat adjuster driver 8-way power,Seat adjuster 8-way power front passenger,Seats heated driver and front passenger,Seat rear split-folding,Seat trim leather seating surfaces,Memory Package 2-position memory driver seat and outside rearview mirrors,Console floor with CD storage,Cup holders 2 front on the floor console,Cup holders ...

Snow blower engine start 13 HP Tecumseh

For hi qual version: www.youtube.com Here's how we achieve one-pull snow blower starting. Bought a model with an engine that has a primer button. Kept the machine in a heated garage. Comfortably checked oil and tire pressure there. Uneven tire pressure can cause the machine to pull to one side. We do NOT start it there. Now its time to get ugly. We wear old clothes. Put in ear plugs. Roll it out into the cold cruel world and close the door. ALWAYS store the gas outside. Yes it is be cold - that is why the primer button is needed. We fill the gas tank before opening the gas tap below the tank. The gas acts as lubrication for the seats/seals on the tap. We make sure the gas tank is venting properly to prevent suction lock. This one needs a notched washer under the cap. Then we urn the ignition switch to on, place the throttle lever to top speed, set the choke lever to full choke, and press the primer button 2-4 times. Usuall hear a slight gurgle of gas, but sometimes it takes a few minutes for gas to percolate fully into the fuel system. Then we sllowly on the manual recoil starter handle to take out the slack and turn the engine over to the compression stroke. The resistance increases as it gets there. We let the recoil started gather in the cord and then pull it quickly. Upon the engine starting, we quickly open the choke and bring back the throttle to a fast idle. We then it run for at least 10 minutes before commencing operation (another coming video on that). This 13 ...

DIY - Bending PVC Pipe with Air Pressure - HenryWitecki.com (Cataclyst) and Chris Powell

UPDATED: MORE INFORMATION ******* Please contact me if you have any questions! cataclyst.info -------Contact Page The motor I used was actually a loaner from a friend, it is about 400 dollars, but is far beyond what the bender requires, it could have turned steel. You need any low speed 20-60rpm (but not necessarily adjustable) decent torque motor . If you're just bending a couple of lengths you might simply turn it by hand. I was bending over 100 12 foot lengths of pipe. For the tube that runs through the rubber stopper, we used lamp rod, which we cross threaded, and loaded with lots of Teflon tape. You would be much better off taking a quick release air coupler to a machinist and asking him to make you 2 threaded tubes that the coupler can screw onto (1 for backup). You could also tap it yourself if you have the tools. You're going to drill out your stopper and run the tube through, put a nylon washer, steel washer then lock washer on either side and tighten down the exposed hex nut once you put it in the end of your pipe to squish the rubber stopper into place. The other side is simply a hex nut, with a nylon washer, steel washer, then hex bolt that clamp the stopper into place. You want your steel washer to be as close in diameter to the inside of your pipe as possible, and you want the interior diameter of your nylon washer to be as close to your threaded tube size as possible. (you want to have to turn it on) www.cataclyst.org This is documentation of a process for ...

Briggs5HP great running motor

This is a briggs and stratton 5hp horizontal shaft this motor didn't run before because of dirty carb. but i cleaned the carb and as you watch you can tell it runs great. this motor used to be used on a pressure washer but is now used on a go kart, but as soon as i put my kart to gether i will show a video of it.